For batteries such as BSLBATT's 51.2V LiFePO4 range, the source that stopped shows where the fault is. If neither solar nor grid charges it, the battery is full, too cold, shut down by its BMS or cut off from the inverter. Solar alone failing points to loads, panels or wiring; grid alone, to inverter settings.
Start Here: Which Charging Source Has Stopped?
Open the monitoring app or look at the inverter screen. Four readings tell you most of what you need:
- SOC: the battery's state of charge. A battery at 100% will not take more.
- PV power: how much the panels are producing right now.
- Load power: how much the house is using.
- Alarms: any battery, grid or communication error code. Write it down.
Most home batteries charge from two sources: the solar panels, and the grid or a generator through the hybrid inverter. Checking which of them still works tells you where to look.
Quick Check: Find Your Symptom
Find your situation in the first column and what you see in the second. Each row points to the check in that situation's section below.
| Situation | What you see | Most likely cause | Where to look |
| 1. No charging at all | SOC reads 100% and charging power is zero | The battery is full | Check 1 |
| No charging on cold mornings, normal again in the afternoon | Charging blocked below 0°C | Check 2 | |
| Battery lights are all off and the inverter cannot find the battery | BMS shutdown after a deep discharge | Check 3 | |
| Inverter shows a battery communication error | CAN or RS485 cable, or protocol setting | Check 4 | |
| The battery's ALM light is on | Voltage, current or temperature protection | Check 5 | |
| 2. Solar not charging | Panels are producing on a sunny day, but the battery SOC does not rise | Loads use all the solar power | Check 1 |
| Battery discharges while the panels produce, and grid figures in the app look wrong | CT clamp reversed or on the wrong cable | Check 2 | |
| PV power is lower than usual on clear days | Shade or dirt on the panels | Check 3 | |
| Inverter shows 0V on the PV input in daylight | Wiring, isolator, breaker or fuse | Check 4 | |
| Off-grid charge controller shows no battery | Battery shut down by its BMS | Check 5 | |
| 3. Grid not charging | The battery never charges from the grid | Grid charging is switched off | Check 1 |
| No charging during off-peak hours, or charging at the wrong time | Time slot or inverter clock is wrong | Check 2 | |
| Grid charging is very slow or stops at a low SOC | Charge current or target SOC set too low | Check 3 | |
| No charging from the grid or a generator, with a fault code | AC input rejected by the inverter | Check 4 | |
| 4. Stops early | Charging always stops at the same level, such as 90% | SOC limit setting | Check 1 |
| Overvoltage alarm near the end of the charge | Lead-acid or wrong charge voltage settings | Check 2 | |
| One battery in a parallel bank always stops first | Parallel bank imbalance | Check 3 |
Situation 1: LiFePO4 Battery Won't Charge From Solar or the Grid
If neither source can charge the battery, the problem is in the battery itself or in its link to the inverter. Work through the checks in order: the first ones are the most common and the quickest to rule out.
The battery's lights help with several of them. On BSLBATT's two 51.2V home battery series, the user manuals define the main patterns like this:
| Light pattern | B-LFP48 rack batteries (100E 3U, 200E, 300E) | Li-Pro wall batteries (5120, 10240, StyX) |
| All lights off | Sleep mode or powered off | Dormancy or undervoltage |
| Alarm light while charging | ALM solid with the SOC lights off: temperature, overcurrent or fault protection has stopped charging | ALM flashing red: charge protection |
| Alarm light at standby | RUN and ALM flashing: module low voltage | ALM flashing yellow: an alarm, or SOC below 20% |
Other brands use different patterns, so check the manual for your model.
Check 1: Is the Battery Already Full?
What you'll see: SOC reads 100% or close to it, and charging power is zero. On BSLBATT's B-LFP48 rack batteries, all SOC lights stay on.
What it means: The BMS has ended the charge because the battery is full. This is normal.
Owner check: Look again in the evening, once the battery has started to discharge. An SOC reading that jumps after a full charge is the BMS recalibrating, not a fault.
Installer fix: If charging always stops at the same level below 100%, look for an SOC limit in the settings (see Situation 4).
Check 2: Is It Too Cold to Charge?
What you'll see: No charging on cold mornings, normal charging in the afternoon, and a low-temperature charging alarm in the app. The battery still powers the house.
What it means: LiFePO4 cells must not be charged below freezing, so the BMS blocks charging until they warm up. BSLBATT's 51.2V home batteries charge between 0°C and 55°C and discharge down to -20°C.
Owner check: Wait for the battery to warm up. The manuals advise checking that the room temperature is within range, shutting the battery down, and restarting it once the temperature is back to normal.
Installer fix: Where winters freeze, install the battery indoors or in a heated space. The same applies at the top of the range: above 55°C the BMS can also stop charging, so keep batteries out of direct sun and hot sheds.
Check 3: Has the Battery Shut Down After a Deep Discharge?
What you'll see: After a power cut or a run of cloudy days, the battery lights are off and the inverter reports no battery.
What it means: The battery ran down until the BMS's low-voltage protection switched off its output to protect the cells. BSLBATT's 51.2V batteries are specified with a 47V discharge cut-off, and the inverter's own cut-off should stop discharge before the BMS has to. To the inverter, a sleeping battery looks the same as a disconnected one.
Owner check:
- Check that the breakers are on, then press the battery's power switch to restart the BMS.
- If the lights come on, let the system charge the battery as soon as possible. BSLBATT's manuals warn that a fully discharged battery should be recharged promptly to avoid damage.
- If an undervoltage alarm shows, leave the battery idle for 30 minutes, then restart the charge.
- If the battery does not power on, stop and call your installer.
Installer fix: Set a low-SOC reserve in the inverter so the battery does not run flat again. On off-grid systems with a separate charge controller, the battery has to be restarted before the controller will charge (see Situation 2, Check 5). How the BMS protects the cells is explained in this guide to what a battery management system (BMS) does.
Check 4: Is the Inverter Talking to the Battery?
What you'll see: The battery lights look normal, but the inverter shows a battery communication error or a BMS fault, or does not detect the lithium battery.
What it means: Most hybrid inverters charge a lithium battery in closed loop: the BMS sends its SOC and the charge voltage and current it will accept over CAN or RS485. If that link drops, many inverters stop charging the battery or raise an alarm.
Owner check: Make sure the communication cable is pushed fully into both the battery and the inverter, and note the error code. Leave the settings to your installer.
Installer fix:
- Use the right port. On BSLBATT's B-LFP48 and Li-Pro batteries, the inverter connects to the CAN port (or, on B-LFP48 models, the separate RS485 inverter port), not to the RS485-1/2 ports that link batteries in parallel.
- Check the cable pinout. Pin assignments differ between inverter brands, so a standard network cable may not work.
- Match the protocol. Select the inverter's protocol in the BMS through the host software or the cloud platform's Inverter Protocol setting, and set the inverter to the matching lithium battery type.
- In a parallel bank, connect the inverter to the master battery.
The user manual for the B-LFP48-100E 3U server rack battery and the rest of the B-LFP48 rack series lists CAN and RS485 protocols for more than 30 inverter brands.
Check 5: Is the Battery Showing an Alarm?
What you'll see: The ALM light is on (solid on B-LFP48 batteries, flashing red on Li-Pro batteries), or the app shows a battery alarm.
What it means: The BMS has stopped charging to protect the cells from overvoltage, undervoltage, overcurrent or temperature.
Owner check: Follow the first step in the battery manual. For BSLBATT batteries:
| Alarm | First step in BSLBATT's manuals |
| Charging low or high temperature | Check that the installation temperature is within the operating range; shut the battery down and restart it once the temperature is back to normal |
| Cell or total overvoltage or undervoltage | Leave the battery idle for 30 minutes, then restart charging |
| Charging overcurrent | Wait 5 minutes; if the battery does not recover, restart the system |
| SOC alarm | Restart the battery, then charge it |
Installer fix: On batteries with the WiFi module, read the alarm history, cell voltages and temperatures in the cloud platform. If the alarm keeps coming back, contact the manufacturer with the serial number and BMS software version. Typical BMS faults are covered in this article on common BMS failures.
Situation 2: Solar Panel Not Charging Battery
If the grid or a generator can still charge the battery, the battery and its communication are fine. The problem is in the panels, their wiring, or how the inverter uses the solar power.
Check 1: Are Your Loads Using All the Solar Power?
What you'll see: The app shows the panels producing, but the battery SOC does not rise.
What it means: In self-consumption mode, a hybrid inverter powers the house first and charges the battery only with what is left. On a short winter day, or while a heat pump, pool pump or EV charger runs, there may be nothing left. Some work modes also export surplus to the grid before charging.
Owner check: Compare PV power with load power in the app. If they are about equal, the system is working as designed. Try again when the big loads are off.
Installer fix: Check that the work mode puts battery charging ahead of export.
Check 2: Is the CT Clamp Installed the Right Way Round?
What you'll see: The battery does not charge from solar, or discharges while the panels are producing, and the app's grid import and export figures look wrong.
What it means: Many hybrid inverters use a current sensor (CT clamp) on the grid cable to measure import and export. If it is reversed or on the wrong cable, the inverter misreads what the house is doing and can send solar power to the grid instead of the battery.
Owner check: Compare the app's grid reading with your electricity meter. If one shows import while the other shows export, tell your installer.
Installer fix: Check the CT clamp's direction arrow, cable and phase against the inverter manual.
Check 3: Are the Panels Shaded or Dirty?
What you'll see: PV power is lower than on similar days last year.
What it means: Shade from trees or new buildings, dust, bird droppings, snow and a low winter sun all cut output. Even partial shade on one panel can pull down a whole string.
Owner check: Look at the panels from the ground for shade and dirt. Clean them only if it is safe, or ask for a cleaning service.
Installer fix: If output is low on clear days with clean panels, test each string for a failed panel or connector.
Check 4: Is the Panel Voltage Reaching the Inverter?
What you'll see: The inverter shows 0V, or a very low voltage, on the PV input in daylight.
What it means: Power is not reaching the inverter, or the string voltage is outside the inverter's MPPT range. A string with too few panels may never reach the start-up voltage. A string with too many can exceed the inverter's maximum input voltage, which risks damaging it, especially on cold mornings when panel voltage is highest.
Owner check: Check that the PV isolator switch is on. Do not open connectors or junction boxes yourself: PV cables can carry several hundred volts in daylight.
Installer fix:
- Check DC breakers and fuses on the PV line, and MC4 connectors for looseness or corrosion.
- Check polarity at the inverter or controller input, especially after rewiring.
- Measure the string's open-circuit voltage: it must stay below the inverter's maximum input voltage, and the operating voltage should sit within the MPPT range.
Check 5: Can the Charge Controller See the Battery?
What you'll see: On an off-grid system with a separate solar charge controller, the controller stays off or shows no battery, even in full sun.
What it means: Many controllers need to read voltage on their battery terminals before they start. If the BMS has shut the battery down after a deep discharge, the controller sees nothing. The panels are fine; the battery has to be restarted first.
Owner check: Restart the battery as described in Situation 1, Check 3.
Installer fix: Follow the controller's connection order: battery connected before the panels, and panels disconnected first. Recommended LiFePO4 settings for 12V, 24V and 48V controllers are listed in this LiFePO4 charging guide.
Situation 3: Inverter Not Charging Battery From the Grid
If solar charges the battery but the grid does not, the battery is fine and the cause is almost always an inverter setting. Grid charging is often off by default, because in self-consumption mode the battery is meant to store solar power.
Check 1: Is Grid Charging Switched On?
What you'll see: The battery never charges from the grid, at any time of day.
What it means: Most hybrid inverters have a separate setting that allows charging from the grid. On Deye hybrid inverters, for example, it is enabled per time slot in the time-of-use settings.
Owner check: Look in the app for a grid charge or charge from grid option and note whether it is on. Ask your installer before changing it.
Installer fix: Enable grid charging in the slots the owner wants.
Check 2: Is It Inside the Charging Time Slot?
What you'll see: Off-peak grid charging has stopped, or happens at the wrong time.
What it means: The time slots, or the inverter's clock, do not match the tariff. Clocks often drift after daylight saving changes or a long power cut.
Owner check: Compare the inverter's clock with the real time, and the charging slot with your off-peak hours.
Installer fix: Correct the clock and slots, and check that the target SOC for each slot is higher than the battery's present SOC.
Check 3: Are the Charge Current and Target SOC Set Too Low?
What you'll see: The battery charges from the grid very slowly, or stops at a low SOC.
What it means: A grid charge current set to zero or very low, or a target SOC below the present SOC, makes the battery look as if it is not charging.
Owner check: Note the charge current and target SOC shown in the app.
Installer fix: Set the grid charge current and SOC targets together, within the battery's rated charge current.
Check 4: Is the Grid or Generator Input Being Rejected?
What you'll see: The inverter shows a grid or generator fault and keeps running from the battery instead of charging it.
What it means: The inverter only accepts an AC source whose voltage and frequency are within its range. A weak grid or a generator with unstable frequency can be rejected.
Owner check: Note the AC input voltage, frequency and fault code on the inverter screen.
Installer fix: Check the AC input settings, and the generator input's own enable setting and charge current, which are often separate from the grid settings.
Situation 4: Battery Charges but Stops Early
If the battery charges but the charge ends too soon, a limit is being reached before the battery is full.
Check 1: Is There an SOC Limit?
What you'll see: Charging stops at the same level every day, such as 90%.
What it means: Many systems cap charging below 100% to reduce time at full charge, or stop at a set SOC in time-of-use mode.
Owner check: Look for a maximum SOC or charge limit in the app.
Installer fix: Set the limit to suit the site. An occasional full charge helps the BMS keep its SOC reading accurate.
Check 2: Are the Charge Voltages Right for LiFePO4?
What you'll see: Charging stops early, or the battery shows an overvoltage alarm near the end of the charge.
What it means: Without closed-loop communication, charge voltages are set by hand. A lead-acid profile uses absorption and equalization voltages set for 24 lead-acid cells, not 16 LiFePO4 cells. The equalization stage in particular goes well above a LiFePO4 battery's limit and trips the BMS's overvoltage protection, which ends the charge.
Owner check: Nothing to change yourself. Tell your installer if the battery type in the settings says lead-acid, AGM or gel.
Installer fix: Use closed-loop communication where the inverter supports it. Otherwise set LiFePO4 values: BSLBATT's 51.2V batteries use a 55V charge voltage, and the Li-Pro series lists a 54.5V float.
Check 3: Are Batteries in Parallel Out of Balance?
What you'll see: In a bank of several batteries, one always reaches full or alarms first, and the charge stops for the whole bank.
What it means: Batteries at different voltages when first connected, old and new batteries mixed together, or address settings that stop the master reading every battery can all end the charge early.
Owner check: Compare each battery's SOC and voltage in the app after a full charge, and tell your installer if one stays apart from the rest.
Installer fix: BSLBATT's B-LFP48 rack manual specifies:
- Before the first parallel power-on, keep the voltage difference between batteries within 5V.
- Switch the batteries on one by one and allow a 5-minute stabilization period.
- Give each battery its own DIP switch address, with the master set to 1. Two batteries with the same address break parallel communication.
- Add new batteries before the existing bank passes one year of use, so their SOC does not drift too far apart.
The Li-Pro wall series, including the Li-Pro StyX 16kWh battery assigns addresses automatically for up to 15 units in parallel, and gives the same one-year expansion advice. Gradual capacity loss across the whole bank is a different problem, covered in this guide on why a home battery loses capacity.
How to Reset Your Solar Battery System Safely
Many charging faults clear after a full restart of the system. Follow the shutdown and start-up order in your battery and inverter manuals. For BSLBATT's B-LFP48 and Li-Pro batteries, the manuals give this sequence:
To shut down:
- Shut down the inverter, following its user manual.
- Switch off the battery with its power switch, and open the breaker between battery and inverter. In a parallel bank, switch off each battery until its lights are off.
- Wait a few minutes before starting up again.
To start up:
- Close the breaker between the inverter and the battery, and the battery's own breaker if it has one.
- Press the battery's power switch. In a parallel bank, switch the batteries on one by one and allow 5 minutes for the system to stabilize.
- Start the inverter, following its user manual.
On off-grid systems with a separate charge controller, disconnect the panels before the battery, and reconnect the battery before the panels.
After an overvoltage or undervoltage alarm, leave the battery idle for 30 minutes before charging again. If the battery does not power on after a restart, do not keep trying.
When to Stop and Call Your Installer
Owner checks are about reading the app, waiting, cleaning and restarting. Call your installer or distributor when:
- the battery does not power on after a restart
- an alarm comes back after the steps in the manual
- the fix means changing inverter settings, communication cables or wiring
- one battery in a bank keeps drifting away from the others
- the battery is swollen, smells or is unusually hot; switch the system off if it is safe to do so and keep away from the battery. If there is smoke or fire, leave and call the emergency services
To speed up the diagnosis, BSLBATT's manuals ask for:
- the serial number and BMS software version
- the installation date, and when and how often the fault happens
- photos or videos of the installation and the indicator lights
- the usage history: how often the battery cycles, charging habits and maintenance
Solar Battery Not Charging FAQ
Q: What causes a solar battery not to charge?
The most common causes are a full battery, temperatures below 0°C, a BMS shutdown after a deep discharge, lost communication with the inverter, PV wiring faults and inverter settings that turn off solar or grid charging. Checking whether solar, grid or both have stopped tells you which group to look at first.
Q: Why is my solar panel not charging my battery?
If the grid can still charge the battery, the house loads may be using all the solar power, the CT clamp may be reversed, or the panels may be shaded, dirty or disconnected. Compare PV power with load power in the app, then check the PV input voltage on the inverter.
Q: Why is my inverter not charging the battery from the grid?
Grid charging is often switched off by default, or allowed only in set time-of-use slots. Check the grid charge setting, the time slots and inverter clock, the charge current and the target SOC. If these are correct, the inverter may be rejecting the AC input because its voltage or frequency is out of range.
Q: Can a LiFePO4 battery charge below 0°C?
No. Standard LiFePO4 batteries should not be charged below 0°C, and their BMS blocks charging until the cells warm up. BSLBATT's 51.2V home batteries charge from 0°C to 55°C and discharge from -20°C to 55°C, so in cold climates install them indoors or in a heated space.
Q: How do I reset a solar battery that won't charge?
Shut down the inverter, switch the battery off and open the breaker between them. Wait a few minutes, close the breaker, switch the battery on, then start the inverter. After an undervoltage or overvoltage alarm, BSLBATT's manuals advise a 30-minute rest before charging again. If the battery does not power on, call your installer.
How Installers Can Prevent Most Charging Call-Outs
Most of the faults in this guide are set up, or prevented, at commissioning. Four steps cover the majority:
- Closed-loop communication with the right protocol, checked in the inverter app before you leave the site.
- A low-SOC reserve in the inverter, so a long outage or cloudy spell does not end in a BMS shutdown.
- A location that stays above 0°C in winter and out of direct sun in summer.
- A matched parallel bank: batteries within 5V of each other at first power-on, unique addresses, and expansion within the first year.
BSLBATT's 51.2V B-LFP48 rack batteries and Li-Pro wall batteries communicate with major hybrid inverter brands over CAN and RS485. With the WiFi module, the cloud platform records cell voltages, temperatures and alarm history, so installers can see why a battery stopped charging before they go to site.
Marketing Director| Focused on ESS · BSLBATT
Aydan is a Marketing Director and energy storage specialist at BSLBATT, focusing on residential, commercial, and off-grid battery solutions. He works closely with solar distributors, installers, and EPC companies across global markets, supporting the design and deployment of reliable energy storage systems.
Post time: Oct-26-2026





